Flip chip bonding technique using transferred microsolder bumps

H. Tsunetsugu, T. Hayashi, M. Hosoya, K. Katsura, M. Hirano, Y. Imai

Research output: Contribution to journalArticle

10 Citations (Scopus)

Abstract

We have improved the microsolder bump technique previously used for fabricating a high-speed photoreceiver for high-speed and wideband coherent optical communication. To eliminate the damage caused by stress during vapor-phase deposition of the solder material and to enable the application of various high-speed electrical and/or photonic devices in conjunction with high-density interconnections, we have developed a flip-chip-bonding technique that uses microsolder bumps with a diameter of about 26 and 40 μm. These bumps are transferred from a carrier substrate to a chip that is then bonded to the final substrate. This technique has three advantages. First, the stress during vapor-phase deposition does not damage the device because the bump formation process is separate from the device formation. Second, many applications are possible because we can make many carrier substrates with various chip sizes and bump pitches on a single Si wafer. Third, the chips with transferred microsolder bumps can be applied to devices that are known to be defect-free because the carrier substrates with the deposited solder bumps are individually aligned face-to-face with the base metal on the devices. We used solder materials of 100% In and 60% Sn-Pb in our experiments. From 8-546 transferred microsolder bumps were successfully formed on 0.5- to 4-mm-square chips (test samples and electrical and photonic devices). We also confirmed that this flip chip bonding was very stable after 1000 heat cycles. This new flip-chip-bonding technique should be very useful for making future high-speed optical transmission systems and the parallel optical interconnections required for electrical and photonic devices that will be used to create stable high-speed and high-density interconnections.

Original languageEnglish
Pages (from-to)327-334
Number of pages8
JournalIEEE transactions on components, packaging and manufacturing technology. Part C. Manufacturing
Volume20
Issue number4
DOIs
Publication statusPublished - 1997 Oct
Externally publishedYes

Fingerprint

Photonic devices
Soldering alloys
Substrates
Vapors
Optical interconnects
Optical communication
Light transmission
Defects
Metals
Experiments

ASJC Scopus subject areas

  • Engineering(all)

Cite this

Flip chip bonding technique using transferred microsolder bumps. / Tsunetsugu, H.; Hayashi, T.; Hosoya, M.; Katsura, K.; Hirano, M.; Imai, Y.

In: IEEE transactions on components, packaging and manufacturing technology. Part C. Manufacturing, Vol. 20, No. 4, 10.1997, p. 327-334.

Research output: Contribution to journalArticle

Tsunetsugu, H. ; Hayashi, T. ; Hosoya, M. ; Katsura, K. ; Hirano, M. ; Imai, Y. / Flip chip bonding technique using transferred microsolder bumps. In: IEEE transactions on components, packaging and manufacturing technology. Part C. Manufacturing. 1997 ; Vol. 20, No. 4. pp. 327-334.
@article{dcaf02c66eb644a789aa3b8aec656e99,
title = "Flip chip bonding technique using transferred microsolder bumps",
abstract = "We have improved the microsolder bump technique previously used for fabricating a high-speed photoreceiver for high-speed and wideband coherent optical communication. To eliminate the damage caused by stress during vapor-phase deposition of the solder material and to enable the application of various high-speed electrical and/or photonic devices in conjunction with high-density interconnections, we have developed a flip-chip-bonding technique that uses microsolder bumps with a diameter of about 26 and 40 μm. These bumps are transferred from a carrier substrate to a chip that is then bonded to the final substrate. This technique has three advantages. First, the stress during vapor-phase deposition does not damage the device because the bump formation process is separate from the device formation. Second, many applications are possible because we can make many carrier substrates with various chip sizes and bump pitches on a single Si wafer. Third, the chips with transferred microsolder bumps can be applied to devices that are known to be defect-free because the carrier substrates with the deposited solder bumps are individually aligned face-to-face with the base metal on the devices. We used solder materials of 100{\%} In and 60{\%} Sn-Pb in our experiments. From 8-546 transferred microsolder bumps were successfully formed on 0.5- to 4-mm-square chips (test samples and electrical and photonic devices). We also confirmed that this flip chip bonding was very stable after 1000 heat cycles. This new flip-chip-bonding technique should be very useful for making future high-speed optical transmission systems and the parallel optical interconnections required for electrical and photonic devices that will be used to create stable high-speed and high-density interconnections.",
author = "H. Tsunetsugu and T. Hayashi and M. Hosoya and K. Katsura and M. Hirano and Y. Imai",
year = "1997",
month = "10",
doi = "10.1109/3476.650965",
language = "English",
volume = "20",
pages = "327--334",
journal = "IEEE transactions on components, packaging and manufacturing technology. Part C. Manufacturing",
issn = "1083-4400",
publisher = "Institute of Electrical and Electronics Engineers Inc.",
number = "4",

}

TY - JOUR

T1 - Flip chip bonding technique using transferred microsolder bumps

AU - Tsunetsugu, H.

AU - Hayashi, T.

AU - Hosoya, M.

AU - Katsura, K.

AU - Hirano, M.

AU - Imai, Y.

PY - 1997/10

Y1 - 1997/10

N2 - We have improved the microsolder bump technique previously used for fabricating a high-speed photoreceiver for high-speed and wideband coherent optical communication. To eliminate the damage caused by stress during vapor-phase deposition of the solder material and to enable the application of various high-speed electrical and/or photonic devices in conjunction with high-density interconnections, we have developed a flip-chip-bonding technique that uses microsolder bumps with a diameter of about 26 and 40 μm. These bumps are transferred from a carrier substrate to a chip that is then bonded to the final substrate. This technique has three advantages. First, the stress during vapor-phase deposition does not damage the device because the bump formation process is separate from the device formation. Second, many applications are possible because we can make many carrier substrates with various chip sizes and bump pitches on a single Si wafer. Third, the chips with transferred microsolder bumps can be applied to devices that are known to be defect-free because the carrier substrates with the deposited solder bumps are individually aligned face-to-face with the base metal on the devices. We used solder materials of 100% In and 60% Sn-Pb in our experiments. From 8-546 transferred microsolder bumps were successfully formed on 0.5- to 4-mm-square chips (test samples and electrical and photonic devices). We also confirmed that this flip chip bonding was very stable after 1000 heat cycles. This new flip-chip-bonding technique should be very useful for making future high-speed optical transmission systems and the parallel optical interconnections required for electrical and photonic devices that will be used to create stable high-speed and high-density interconnections.

AB - We have improved the microsolder bump technique previously used for fabricating a high-speed photoreceiver for high-speed and wideband coherent optical communication. To eliminate the damage caused by stress during vapor-phase deposition of the solder material and to enable the application of various high-speed electrical and/or photonic devices in conjunction with high-density interconnections, we have developed a flip-chip-bonding technique that uses microsolder bumps with a diameter of about 26 and 40 μm. These bumps are transferred from a carrier substrate to a chip that is then bonded to the final substrate. This technique has three advantages. First, the stress during vapor-phase deposition does not damage the device because the bump formation process is separate from the device formation. Second, many applications are possible because we can make many carrier substrates with various chip sizes and bump pitches on a single Si wafer. Third, the chips with transferred microsolder bumps can be applied to devices that are known to be defect-free because the carrier substrates with the deposited solder bumps are individually aligned face-to-face with the base metal on the devices. We used solder materials of 100% In and 60% Sn-Pb in our experiments. From 8-546 transferred microsolder bumps were successfully formed on 0.5- to 4-mm-square chips (test samples and electrical and photonic devices). We also confirmed that this flip chip bonding was very stable after 1000 heat cycles. This new flip-chip-bonding technique should be very useful for making future high-speed optical transmission systems and the parallel optical interconnections required for electrical and photonic devices that will be used to create stable high-speed and high-density interconnections.

UR - http://www.scopus.com/inward/record.url?scp=0031246511&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=0031246511&partnerID=8YFLogxK

U2 - 10.1109/3476.650965

DO - 10.1109/3476.650965

M3 - Article

VL - 20

SP - 327

EP - 334

JO - IEEE transactions on components, packaging and manufacturing technology. Part C. Manufacturing

JF - IEEE transactions on components, packaging and manufacturing technology. Part C. Manufacturing

SN - 1083-4400

IS - 4

ER -