Fluid motion and heat transfer of boiling with impinging flow in a mini-tube with nonlinear thermocapillary solutions

Naoki Ono, Atsushi Hamaoka, Yuta Otsubo

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

Boiling heat transfer with impinging flow can be an effective way for cooling a small heated area such as CPUs and laser emitting devices. In the phenomena the movement of liquid layer on the heated surface strongly affects the detachment of boiling bubbles and the heat flux. In this study, nonlinear thermocapillary solutions such as button aqueous solutions were applied to this type of boiling with impinging flow aiming to promote heat transfer. These solutions have special characteristics that the surface tension increases as the temperature is raised over some temperature. It is expected that this tendency about the surface tension will promote the wetting of the heated surface and the detachment of boiling bubbles. In the experiment, T-shaped mini tubes were built with quartz tubes and used for flow boiling. The inner diameter of the tube was 2 mm and the outer diameter was 4 mm. The liquid flow impinged at the junction point where small area was heated by using a conducting thin film coated at the outer surface of the tube. The test fluids were butanol aqueous solution and pure water. The flow rate of the liquid was the order of 1 ml/min, the concentration of the butanol aqueous solution was 7.15 wt %. The liquid motion was observed by CCD video camera system. It was found from the experiment that the motion of the liquid layer of the butanol solution at the impinging area was very different from that of pure water. The layer of the butanol solution tended to extend to the hotter part of the heated area. In another experiment for precisely fixing the imposed heat flux value, T-shaped mini channel with small copper surface installed for heating the fluid was prepared. The cross section of the channel was rectangular shape of 3 mm x 3 mm, and the entire channel was made of insulating polymer material. It was found that the heat transfer of the boiling with impinging flow in using butanol solution was more promoted than that in using pure water.

Original languageEnglish
Title of host publication2010 14th International Heat Transfer Conference, IHTC 14
Pages541-546
Number of pages6
Volume5
DOIs
Publication statusPublished - 2010
Event2010 14th International Heat Transfer Conference, IHTC 14 - Washington, DC
Duration: 2010 Aug 82010 Aug 13

Other

Other2010 14th International Heat Transfer Conference, IHTC 14
CityWashington, DC
Period10/8/810/8/13

Fingerprint

Boiling liquids
Butanols
Heat transfer
Butenes
Fluids
Liquids
Bubbles (in fluids)
Surface tension
Water
Heat flux
Quartz
Experiments
Video cameras
CCD cameras
Program processors
Wetting
Copper
Polymers
Flow rate
Cooling

ASJC Scopus subject areas

  • Fluid Flow and Transfer Processes

Cite this

Ono, N., Hamaoka, A., & Otsubo, Y. (2010). Fluid motion and heat transfer of boiling with impinging flow in a mini-tube with nonlinear thermocapillary solutions. In 2010 14th International Heat Transfer Conference, IHTC 14 (Vol. 5, pp. 541-546) https://doi.org/10.1115/IHTC14-22498

Fluid motion and heat transfer of boiling with impinging flow in a mini-tube with nonlinear thermocapillary solutions. / Ono, Naoki; Hamaoka, Atsushi; Otsubo, Yuta.

2010 14th International Heat Transfer Conference, IHTC 14. Vol. 5 2010. p. 541-546.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Ono, N, Hamaoka, A & Otsubo, Y 2010, Fluid motion and heat transfer of boiling with impinging flow in a mini-tube with nonlinear thermocapillary solutions. in 2010 14th International Heat Transfer Conference, IHTC 14. vol. 5, pp. 541-546, 2010 14th International Heat Transfer Conference, IHTC 14, Washington, DC, 10/8/8. https://doi.org/10.1115/IHTC14-22498
Ono N, Hamaoka A, Otsubo Y. Fluid motion and heat transfer of boiling with impinging flow in a mini-tube with nonlinear thermocapillary solutions. In 2010 14th International Heat Transfer Conference, IHTC 14. Vol. 5. 2010. p. 541-546 https://doi.org/10.1115/IHTC14-22498
Ono, Naoki ; Hamaoka, Atsushi ; Otsubo, Yuta. / Fluid motion and heat transfer of boiling with impinging flow in a mini-tube with nonlinear thermocapillary solutions. 2010 14th International Heat Transfer Conference, IHTC 14. Vol. 5 2010. pp. 541-546
@inproceedings{662147e11b3b41c78e72eefb5b7d3881,
title = "Fluid motion and heat transfer of boiling with impinging flow in a mini-tube with nonlinear thermocapillary solutions",
abstract = "Boiling heat transfer with impinging flow can be an effective way for cooling a small heated area such as CPUs and laser emitting devices. In the phenomena the movement of liquid layer on the heated surface strongly affects the detachment of boiling bubbles and the heat flux. In this study, nonlinear thermocapillary solutions such as button aqueous solutions were applied to this type of boiling with impinging flow aiming to promote heat transfer. These solutions have special characteristics that the surface tension increases as the temperature is raised over some temperature. It is expected that this tendency about the surface tension will promote the wetting of the heated surface and the detachment of boiling bubbles. In the experiment, T-shaped mini tubes were built with quartz tubes and used for flow boiling. The inner diameter of the tube was 2 mm and the outer diameter was 4 mm. The liquid flow impinged at the junction point where small area was heated by using a conducting thin film coated at the outer surface of the tube. The test fluids were butanol aqueous solution and pure water. The flow rate of the liquid was the order of 1 ml/min, the concentration of the butanol aqueous solution was 7.15 wt {\%}. The liquid motion was observed by CCD video camera system. It was found from the experiment that the motion of the liquid layer of the butanol solution at the impinging area was very different from that of pure water. The layer of the butanol solution tended to extend to the hotter part of the heated area. In another experiment for precisely fixing the imposed heat flux value, T-shaped mini channel with small copper surface installed for heating the fluid was prepared. The cross section of the channel was rectangular shape of 3 mm x 3 mm, and the entire channel was made of insulating polymer material. It was found that the heat transfer of the boiling with impinging flow in using butanol solution was more promoted than that in using pure water.",
author = "Naoki Ono and Atsushi Hamaoka and Yuta Otsubo",
year = "2010",
doi = "10.1115/IHTC14-22498",
language = "English",
isbn = "9780791849408",
volume = "5",
pages = "541--546",
booktitle = "2010 14th International Heat Transfer Conference, IHTC 14",

}

TY - GEN

T1 - Fluid motion and heat transfer of boiling with impinging flow in a mini-tube with nonlinear thermocapillary solutions

AU - Ono, Naoki

AU - Hamaoka, Atsushi

AU - Otsubo, Yuta

PY - 2010

Y1 - 2010

N2 - Boiling heat transfer with impinging flow can be an effective way for cooling a small heated area such as CPUs and laser emitting devices. In the phenomena the movement of liquid layer on the heated surface strongly affects the detachment of boiling bubbles and the heat flux. In this study, nonlinear thermocapillary solutions such as button aqueous solutions were applied to this type of boiling with impinging flow aiming to promote heat transfer. These solutions have special characteristics that the surface tension increases as the temperature is raised over some temperature. It is expected that this tendency about the surface tension will promote the wetting of the heated surface and the detachment of boiling bubbles. In the experiment, T-shaped mini tubes were built with quartz tubes and used for flow boiling. The inner diameter of the tube was 2 mm and the outer diameter was 4 mm. The liquid flow impinged at the junction point where small area was heated by using a conducting thin film coated at the outer surface of the tube. The test fluids were butanol aqueous solution and pure water. The flow rate of the liquid was the order of 1 ml/min, the concentration of the butanol aqueous solution was 7.15 wt %. The liquid motion was observed by CCD video camera system. It was found from the experiment that the motion of the liquid layer of the butanol solution at the impinging area was very different from that of pure water. The layer of the butanol solution tended to extend to the hotter part of the heated area. In another experiment for precisely fixing the imposed heat flux value, T-shaped mini channel with small copper surface installed for heating the fluid was prepared. The cross section of the channel was rectangular shape of 3 mm x 3 mm, and the entire channel was made of insulating polymer material. It was found that the heat transfer of the boiling with impinging flow in using butanol solution was more promoted than that in using pure water.

AB - Boiling heat transfer with impinging flow can be an effective way for cooling a small heated area such as CPUs and laser emitting devices. In the phenomena the movement of liquid layer on the heated surface strongly affects the detachment of boiling bubbles and the heat flux. In this study, nonlinear thermocapillary solutions such as button aqueous solutions were applied to this type of boiling with impinging flow aiming to promote heat transfer. These solutions have special characteristics that the surface tension increases as the temperature is raised over some temperature. It is expected that this tendency about the surface tension will promote the wetting of the heated surface and the detachment of boiling bubbles. In the experiment, T-shaped mini tubes were built with quartz tubes and used for flow boiling. The inner diameter of the tube was 2 mm and the outer diameter was 4 mm. The liquid flow impinged at the junction point where small area was heated by using a conducting thin film coated at the outer surface of the tube. The test fluids were butanol aqueous solution and pure water. The flow rate of the liquid was the order of 1 ml/min, the concentration of the butanol aqueous solution was 7.15 wt %. The liquid motion was observed by CCD video camera system. It was found from the experiment that the motion of the liquid layer of the butanol solution at the impinging area was very different from that of pure water. The layer of the butanol solution tended to extend to the hotter part of the heated area. In another experiment for precisely fixing the imposed heat flux value, T-shaped mini channel with small copper surface installed for heating the fluid was prepared. The cross section of the channel was rectangular shape of 3 mm x 3 mm, and the entire channel was made of insulating polymer material. It was found that the heat transfer of the boiling with impinging flow in using butanol solution was more promoted than that in using pure water.

UR - http://www.scopus.com/inward/record.url?scp=84860501664&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84860501664&partnerID=8YFLogxK

U2 - 10.1115/IHTC14-22498

DO - 10.1115/IHTC14-22498

M3 - Conference contribution

SN - 9780791849408

VL - 5

SP - 541

EP - 546

BT - 2010 14th International Heat Transfer Conference, IHTC 14

ER -