Relationship between impact velocity of Al2O3 particles and deposition efficiency in aerosol deposition method

Kazuaki Naoe, Masashi Nishiki, Atsushi Yumoto

Research output: Contribution to journalArticle

21 Citations (Scopus)

Abstract

Aerosol deposition method (ADM) is a technique to form dense films by impacting solid particles to a substrate at room temperature. To improve the deposition efficiency in ADM, the relationship between the impact velocity of Al2O3 particles and the deposition efficiency was investigated in this study. Relative difference in impact particle velocity was evaluated by the increment percentage of the substrate surface area after deposition (ΔS). It is thought that the increase of ΔS means the increase of the impact particle velocity. When ΔS was lower than 10 %, the deposition efficiency increased from 0.082 to 0.104 % as ΔS increased from 3.46 to 9.25 %. Increasing impact particle velocity could promote the bonding between the particles themselves. On the other hand, when ΔS was higher than 10 %, the erosion of the film was observed and the deposition efficiency decreased to about 0.02 % as ΔS increased to about 40 %. SEM observation revealed that cracks parallel to the film surface were propagated. There is a possibility that this tendency of the deposition efficiency toward the impact particle velocity is common among the methods for forming ceramic films by impacting solid ceramic particles.

Original languageEnglish
Pages (from-to)1267-1274
Number of pages8
JournalJournal of Thermal Spray Technology
Volume22
Issue number8
DOIs
Publication statusPublished - 2013 Dec

Fingerprint

impact velocity
Aerosols
Particles (particulate matter)
aerosols
ceramics
Substrates
erosion
Erosion
tendencies
cracks
Cracks
Scanning electron microscopy
scanning electron microscopy
room temperature

Keywords

  • aerosol deposition method
  • alumina
  • deposition efficiency
  • particle velocity

ASJC Scopus subject areas

  • Condensed Matter Physics
  • Materials Chemistry
  • Surfaces, Coatings and Films

Cite this

Relationship between impact velocity of Al2O3 particles and deposition efficiency in aerosol deposition method. / Naoe, Kazuaki; Nishiki, Masashi; Yumoto, Atsushi.

In: Journal of Thermal Spray Technology, Vol. 22, No. 8, 12.2013, p. 1267-1274.

Research output: Contribution to journalArticle

@article{3ef3913d11734394b942503bcc99a5ca,
title = "Relationship between impact velocity of Al2O3 particles and deposition efficiency in aerosol deposition method",
abstract = "Aerosol deposition method (ADM) is a technique to form dense films by impacting solid particles to a substrate at room temperature. To improve the deposition efficiency in ADM, the relationship between the impact velocity of Al2O3 particles and the deposition efficiency was investigated in this study. Relative difference in impact particle velocity was evaluated by the increment percentage of the substrate surface area after deposition (ΔS). It is thought that the increase of ΔS means the increase of the impact particle velocity. When ΔS was lower than 10 {\%}, the deposition efficiency increased from 0.082 to 0.104 {\%} as ΔS increased from 3.46 to 9.25 {\%}. Increasing impact particle velocity could promote the bonding between the particles themselves. On the other hand, when ΔS was higher than 10 {\%}, the erosion of the film was observed and the deposition efficiency decreased to about 0.02 {\%} as ΔS increased to about 40 {\%}. SEM observation revealed that cracks parallel to the film surface were propagated. There is a possibility that this tendency of the deposition efficiency toward the impact particle velocity is common among the methods for forming ceramic films by impacting solid ceramic particles.",
keywords = "aerosol deposition method, alumina, deposition efficiency, particle velocity",
author = "Kazuaki Naoe and Masashi Nishiki and Atsushi Yumoto",
year = "2013",
month = "12",
doi = "10.1007/s11666-013-0031-8",
language = "English",
volume = "22",
pages = "1267--1274",
journal = "Journal of Thermal Spray Technology",
issn = "1059-9630",
publisher = "Springer New York",
number = "8",

}

TY - JOUR

T1 - Relationship between impact velocity of Al2O3 particles and deposition efficiency in aerosol deposition method

AU - Naoe, Kazuaki

AU - Nishiki, Masashi

AU - Yumoto, Atsushi

PY - 2013/12

Y1 - 2013/12

N2 - Aerosol deposition method (ADM) is a technique to form dense films by impacting solid particles to a substrate at room temperature. To improve the deposition efficiency in ADM, the relationship between the impact velocity of Al2O3 particles and the deposition efficiency was investigated in this study. Relative difference in impact particle velocity was evaluated by the increment percentage of the substrate surface area after deposition (ΔS). It is thought that the increase of ΔS means the increase of the impact particle velocity. When ΔS was lower than 10 %, the deposition efficiency increased from 0.082 to 0.104 % as ΔS increased from 3.46 to 9.25 %. Increasing impact particle velocity could promote the bonding between the particles themselves. On the other hand, when ΔS was higher than 10 %, the erosion of the film was observed and the deposition efficiency decreased to about 0.02 % as ΔS increased to about 40 %. SEM observation revealed that cracks parallel to the film surface were propagated. There is a possibility that this tendency of the deposition efficiency toward the impact particle velocity is common among the methods for forming ceramic films by impacting solid ceramic particles.

AB - Aerosol deposition method (ADM) is a technique to form dense films by impacting solid particles to a substrate at room temperature. To improve the deposition efficiency in ADM, the relationship between the impact velocity of Al2O3 particles and the deposition efficiency was investigated in this study. Relative difference in impact particle velocity was evaluated by the increment percentage of the substrate surface area after deposition (ΔS). It is thought that the increase of ΔS means the increase of the impact particle velocity. When ΔS was lower than 10 %, the deposition efficiency increased from 0.082 to 0.104 % as ΔS increased from 3.46 to 9.25 %. Increasing impact particle velocity could promote the bonding between the particles themselves. On the other hand, when ΔS was higher than 10 %, the erosion of the film was observed and the deposition efficiency decreased to about 0.02 % as ΔS increased to about 40 %. SEM observation revealed that cracks parallel to the film surface were propagated. There is a possibility that this tendency of the deposition efficiency toward the impact particle velocity is common among the methods for forming ceramic films by impacting solid ceramic particles.

KW - aerosol deposition method

KW - alumina

KW - deposition efficiency

KW - particle velocity

UR - http://www.scopus.com/inward/record.url?scp=84890552401&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84890552401&partnerID=8YFLogxK

U2 - 10.1007/s11666-013-0031-8

DO - 10.1007/s11666-013-0031-8

M3 - Article

AN - SCOPUS:84890552401

VL - 22

SP - 1267

EP - 1274

JO - Journal of Thermal Spray Technology

JF - Journal of Thermal Spray Technology

SN - 1059-9630

IS - 8

ER -