Optimal load-shedding using local information

Goro Fujita, Goro Shirai

研究成果: Article

抄録

This paper describes an optimal load-shedding policy based on quadratic programming using only some power system state variables after severe generation outages. When generation outage is severe, the imbalance between supply and demand causes a declining frequency. Utilities generators cannot be operated excessively at frequencies above normal. Some of the load must be shed to prevent system damage. Optimal load-shedding policies have been studied using all state variables of the power system. However, in real power system operations, it is difficult to obtain remote information in that fraction of a second following generation outages. An optimal load-shedding method is constructed in this research using quadratic programming (QP) under the assumption that all power system state variables can be available. However, these state variables cannot be easily accessible (as already mentioned). A suboptimal load-shedding scheme based on the local state variables is then studied. The proposed load-shedding method is based on the aforementioned optimal one. The change in line-power flows and the amount of generation power outage are used as accessible data at each load point. Incorporating this local information into the optimal load-shedding method based on the QP method, the proposed load-shedding method is established here. The effectiveness of this proposed method is illustrated by two examples and simulation results on a model power system show that the method is encouraging.

元の言語English
ページ(範囲)32-51
ページ数20
ジャーナルElectrical Engineering in Japan (English translation of Denki Gakkai Ronbunshi)
116
発行部数2
出版物ステータスPublished - 1996
外部発表Yes

Fingerprint

Outages
Quadratic programming
Power generation

ASJC Scopus subject areas

  • Electrical and Electronic Engineering

これを引用

@article{4b1b0f0657954f2d99267ccb9f806ab1,
title = "Optimal load-shedding using local information",
abstract = "This paper describes an optimal load-shedding policy based on quadratic programming using only some power system state variables after severe generation outages. When generation outage is severe, the imbalance between supply and demand causes a declining frequency. Utilities generators cannot be operated excessively at frequencies above normal. Some of the load must be shed to prevent system damage. Optimal load-shedding policies have been studied using all state variables of the power system. However, in real power system operations, it is difficult to obtain remote information in that fraction of a second following generation outages. An optimal load-shedding method is constructed in this research using quadratic programming (QP) under the assumption that all power system state variables can be available. However, these state variables cannot be easily accessible (as already mentioned). A suboptimal load-shedding scheme based on the local state variables is then studied. The proposed load-shedding method is based on the aforementioned optimal one. The change in line-power flows and the amount of generation power outage are used as accessible data at each load point. Incorporating this local information into the optimal load-shedding method based on the QP method, the proposed load-shedding method is established here. The effectiveness of this proposed method is illustrated by two examples and simulation results on a model power system show that the method is encouraging.",
keywords = "Load-shedding, Optimization, Power flow calculation, Power generation outage, Quadratic programming, Under-frequency relay",
author = "Goro Fujita and Goro Shirai",
year = "1996",
language = "English",
volume = "116",
pages = "32--51",
journal = "Electrical Engineering in Japan (English translation of Denki Gakkai Ronbunshi)",
issn = "0424-7760",
publisher = "John Wiley and Sons Inc.",
number = "2",

}

TY - JOUR

T1 - Optimal load-shedding using local information

AU - Fujita, Goro

AU - Shirai, Goro

PY - 1996

Y1 - 1996

N2 - This paper describes an optimal load-shedding policy based on quadratic programming using only some power system state variables after severe generation outages. When generation outage is severe, the imbalance between supply and demand causes a declining frequency. Utilities generators cannot be operated excessively at frequencies above normal. Some of the load must be shed to prevent system damage. Optimal load-shedding policies have been studied using all state variables of the power system. However, in real power system operations, it is difficult to obtain remote information in that fraction of a second following generation outages. An optimal load-shedding method is constructed in this research using quadratic programming (QP) under the assumption that all power system state variables can be available. However, these state variables cannot be easily accessible (as already mentioned). A suboptimal load-shedding scheme based on the local state variables is then studied. The proposed load-shedding method is based on the aforementioned optimal one. The change in line-power flows and the amount of generation power outage are used as accessible data at each load point. Incorporating this local information into the optimal load-shedding method based on the QP method, the proposed load-shedding method is established here. The effectiveness of this proposed method is illustrated by two examples and simulation results on a model power system show that the method is encouraging.

AB - This paper describes an optimal load-shedding policy based on quadratic programming using only some power system state variables after severe generation outages. When generation outage is severe, the imbalance between supply and demand causes a declining frequency. Utilities generators cannot be operated excessively at frequencies above normal. Some of the load must be shed to prevent system damage. Optimal load-shedding policies have been studied using all state variables of the power system. However, in real power system operations, it is difficult to obtain remote information in that fraction of a second following generation outages. An optimal load-shedding method is constructed in this research using quadratic programming (QP) under the assumption that all power system state variables can be available. However, these state variables cannot be easily accessible (as already mentioned). A suboptimal load-shedding scheme based on the local state variables is then studied. The proposed load-shedding method is based on the aforementioned optimal one. The change in line-power flows and the amount of generation power outage are used as accessible data at each load point. Incorporating this local information into the optimal load-shedding method based on the QP method, the proposed load-shedding method is established here. The effectiveness of this proposed method is illustrated by two examples and simulation results on a model power system show that the method is encouraging.

KW - Load-shedding

KW - Optimization

KW - Power flow calculation

KW - Power generation outage

KW - Quadratic programming

KW - Under-frequency relay

UR - http://www.scopus.com/inward/record.url?scp=0030081129&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=0030081129&partnerID=8YFLogxK

M3 - Article

AN - SCOPUS:0030081129

VL - 116

SP - 32

EP - 51

JO - Electrical Engineering in Japan (English translation of Denki Gakkai Ronbunshi)

JF - Electrical Engineering in Japan (English translation of Denki Gakkai Ronbunshi)

SN - 0424-7760

IS - 2

ER -