Study on high speed milling of steam turbine blade materials - Difference in cutting characteristics by alloying elements of stainless steel

Tomonori Kimura, Takekazu Sawa, Tatsuyuki Kamijyo

研究成果: Conference contribution

抄録

In this study, high speed milling of stainless steel was tried for purpose of high efficiency cutting of a steam turbine blade. In the experiment, cutting tool used TiAlN coating radius solid end mill made of cemented carbide. Diameter of end mill is 5mm. Corner radius is 0.2mm. Cutting speed carried out at 100m/s~600m/s. Work pieces was used in the experiment are four kinds of stainless steel which alloy elements differ. Mainly, content of chromium and nickel is different. There are many researches about high speed milling [1, 2]. However, the researches which examined relationship between alloy elements of stainless steel and cutting characteristics on high speed milling using small diameter endmill are few. As the results, in the case of stainless steel containing much nickel, tool life becomes short in high speed cutting area. This reason is nickel has low thermal conductivity. Because the cutting point temperature becomes higher. If the coating removes, wear becomes large rapidly. In other words, maximum limit value of cutting speed was found to be dependent on heat resistance temperature of the coating. On the other hand, Chromium has the effect of improving the abrasion resistant of the workpiece. However, Flank wear was not increased in a low cutting speed area. In the range of this experimental condition, chromium didn't influence tool life. When cutting point temperature is below heat resistant temperature of the coating, it is thought that effect of the coating is maintained. Namely, it was found that appropriate cutting speed followed heat resistant temperature of the coating.

元の言語English
ホスト出版物のタイトルAdvances in Abrasive Technology XIX
出版者Trans Tech Publications Ltd
ページ439-444
ページ数6
874
ISBN(印刷物)9783035710342
DOI
出版物ステータスPublished - 2016
イベント19th International Symposium on Advances in Abrasive Technology, ISAAT 2016 - Stockholm, Sweden
継続期間: 2016 10 22016 10 5

出版物シリーズ

名前Materials Science Forum
874
ISSN(印刷物)02555476

Other

Other19th International Symposium on Advances in Abrasive Technology, ISAAT 2016
Sweden
Stockholm
期間16/10/216/10/5

Fingerprint

steam turbines
turbine blades
Stainless Steel
Steam turbines
Alloying elements
Turbomachine blades
alloying
stainless steels
Stainless steel
high speed
Coatings
coatings
Chromium
Nickel
chromium
nickel
Temperature
Wear of materials
Milling (machining)
heat

ASJC Scopus subject areas

  • Materials Science(all)
  • Condensed Matter Physics
  • Mechanics of Materials
  • Mechanical Engineering

これを引用

Kimura, T., Sawa, T., & Kamijyo, T. (2016). Study on high speed milling of steam turbine blade materials - Difference in cutting characteristics by alloying elements of stainless steel. : Advances in Abrasive Technology XIX (巻 874, pp. 439-444). (Materials Science Forum; 巻数 874). Trans Tech Publications Ltd. https://doi.org/10.4028/www.scientific.net/MSF.874.439

Study on high speed milling of steam turbine blade materials - Difference in cutting characteristics by alloying elements of stainless steel. / Kimura, Tomonori; Sawa, Takekazu; Kamijyo, Tatsuyuki.

Advances in Abrasive Technology XIX. 巻 874 Trans Tech Publications Ltd, 2016. p. 439-444 (Materials Science Forum; 巻 874).

研究成果: Conference contribution

Kimura, T, Sawa, T & Kamijyo, T 2016, Study on high speed milling of steam turbine blade materials - Difference in cutting characteristics by alloying elements of stainless steel. : Advances in Abrasive Technology XIX. 巻. 874, Materials Science Forum, 巻. 874, Trans Tech Publications Ltd, pp. 439-444, 19th International Symposium on Advances in Abrasive Technology, ISAAT 2016, Stockholm, Sweden, 16/10/2. https://doi.org/10.4028/www.scientific.net/MSF.874.439
Kimura T, Sawa T, Kamijyo T. Study on high speed milling of steam turbine blade materials - Difference in cutting characteristics by alloying elements of stainless steel. : Advances in Abrasive Technology XIX. 巻 874. Trans Tech Publications Ltd. 2016. p. 439-444. (Materials Science Forum). https://doi.org/10.4028/www.scientific.net/MSF.874.439
Kimura, Tomonori ; Sawa, Takekazu ; Kamijyo, Tatsuyuki. / Study on high speed milling of steam turbine blade materials - Difference in cutting characteristics by alloying elements of stainless steel. Advances in Abrasive Technology XIX. 巻 874 Trans Tech Publications Ltd, 2016. pp. 439-444 (Materials Science Forum).
@inproceedings{41d778a2b5144675bf6990edd61fadc5,
title = "Study on high speed milling of steam turbine blade materials - Difference in cutting characteristics by alloying elements of stainless steel",
abstract = "In this study, high speed milling of stainless steel was tried for purpose of high efficiency cutting of a steam turbine blade. In the experiment, cutting tool used TiAlN coating radius solid end mill made of cemented carbide. Diameter of end mill is 5mm. Corner radius is 0.2mm. Cutting speed carried out at 100m/s~600m/s. Work pieces was used in the experiment are four kinds of stainless steel which alloy elements differ. Mainly, content of chromium and nickel is different. There are many researches about high speed milling [1, 2]. However, the researches which examined relationship between alloy elements of stainless steel and cutting characteristics on high speed milling using small diameter endmill are few. As the results, in the case of stainless steel containing much nickel, tool life becomes short in high speed cutting area. This reason is nickel has low thermal conductivity. Because the cutting point temperature becomes higher. If the coating removes, wear becomes large rapidly. In other words, maximum limit value of cutting speed was found to be dependent on heat resistance temperature of the coating. On the other hand, Chromium has the effect of improving the abrasion resistant of the workpiece. However, Flank wear was not increased in a low cutting speed area. In the range of this experimental condition, chromium didn't influence tool life. When cutting point temperature is below heat resistant temperature of the coating, it is thought that effect of the coating is maintained. Namely, it was found that appropriate cutting speed followed heat resistant temperature of the coating.",
keywords = "13Cr, Alloying elements, Chromium, High speed cutting, High speed milling, Nickel, Radius end mill, Stainless steel, Steam turbine blade",
author = "Tomonori Kimura and Takekazu Sawa and Tatsuyuki Kamijyo",
year = "2016",
doi = "10.4028/www.scientific.net/MSF.874.439",
language = "English",
isbn = "9783035710342",
volume = "874",
series = "Materials Science Forum",
publisher = "Trans Tech Publications Ltd",
pages = "439--444",
booktitle = "Advances in Abrasive Technology XIX",

}

TY - GEN

T1 - Study on high speed milling of steam turbine blade materials - Difference in cutting characteristics by alloying elements of stainless steel

AU - Kimura, Tomonori

AU - Sawa, Takekazu

AU - Kamijyo, Tatsuyuki

PY - 2016

Y1 - 2016

N2 - In this study, high speed milling of stainless steel was tried for purpose of high efficiency cutting of a steam turbine blade. In the experiment, cutting tool used TiAlN coating radius solid end mill made of cemented carbide. Diameter of end mill is 5mm. Corner radius is 0.2mm. Cutting speed carried out at 100m/s~600m/s. Work pieces was used in the experiment are four kinds of stainless steel which alloy elements differ. Mainly, content of chromium and nickel is different. There are many researches about high speed milling [1, 2]. However, the researches which examined relationship between alloy elements of stainless steel and cutting characteristics on high speed milling using small diameter endmill are few. As the results, in the case of stainless steel containing much nickel, tool life becomes short in high speed cutting area. This reason is nickel has low thermal conductivity. Because the cutting point temperature becomes higher. If the coating removes, wear becomes large rapidly. In other words, maximum limit value of cutting speed was found to be dependent on heat resistance temperature of the coating. On the other hand, Chromium has the effect of improving the abrasion resistant of the workpiece. However, Flank wear was not increased in a low cutting speed area. In the range of this experimental condition, chromium didn't influence tool life. When cutting point temperature is below heat resistant temperature of the coating, it is thought that effect of the coating is maintained. Namely, it was found that appropriate cutting speed followed heat resistant temperature of the coating.

AB - In this study, high speed milling of stainless steel was tried for purpose of high efficiency cutting of a steam turbine blade. In the experiment, cutting tool used TiAlN coating radius solid end mill made of cemented carbide. Diameter of end mill is 5mm. Corner radius is 0.2mm. Cutting speed carried out at 100m/s~600m/s. Work pieces was used in the experiment are four kinds of stainless steel which alloy elements differ. Mainly, content of chromium and nickel is different. There are many researches about high speed milling [1, 2]. However, the researches which examined relationship between alloy elements of stainless steel and cutting characteristics on high speed milling using small diameter endmill are few. As the results, in the case of stainless steel containing much nickel, tool life becomes short in high speed cutting area. This reason is nickel has low thermal conductivity. Because the cutting point temperature becomes higher. If the coating removes, wear becomes large rapidly. In other words, maximum limit value of cutting speed was found to be dependent on heat resistance temperature of the coating. On the other hand, Chromium has the effect of improving the abrasion resistant of the workpiece. However, Flank wear was not increased in a low cutting speed area. In the range of this experimental condition, chromium didn't influence tool life. When cutting point temperature is below heat resistant temperature of the coating, it is thought that effect of the coating is maintained. Namely, it was found that appropriate cutting speed followed heat resistant temperature of the coating.

KW - 13Cr

KW - Alloying elements

KW - Chromium

KW - High speed cutting

KW - High speed milling

KW - Nickel

KW - Radius end mill

KW - Stainless steel

KW - Steam turbine blade

UR - http://www.scopus.com/inward/record.url?scp=84991720613&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84991720613&partnerID=8YFLogxK

U2 - 10.4028/www.scientific.net/MSF.874.439

DO - 10.4028/www.scientific.net/MSF.874.439

M3 - Conference contribution

AN - SCOPUS:84991720613

SN - 9783035710342

VL - 874

T3 - Materials Science Forum

SP - 439

EP - 444

BT - Advances in Abrasive Technology XIX

PB - Trans Tech Publications Ltd

ER -